Black & Decker Cordless Drill Black & Decker Cordless Drill User Manual

0.2

Out of 1 Ratings

Owner's of the Black & Decker Cordless Drill Black & Decker Cordless Drill gave it a score of 0.2 out of 5. Here's how the scores stacked up:

  • Reliability

    1.0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 48
 
11
•  Insertthebitshaftintothechuck.
•  Firmlytightenthechuckbyturningthefrontpartcounterclockwise.
•  Toremovethescrewdriverbitfromtheholder,liftthebitfromtherecess.
•  Tostorethescrewdriverbit,firmlypushitintotheholder(10).
SCREW DRIVING
• Always use the correct type and size of screwdriver bit.
• If screws are difficult to tighten, try applying a small amount of washing liquid or soap as a lubricant.
• Always hold the tool and screwdriver bit in a straight line with the screw.
•
For driving fasteners, the reversing button should be pushed to the left. Use reverse (button
pushed to the right) for removing fasteners. When moving from forward to reverse, or vice
versa, always release the trigger switch first.
KEYLESS CHUCK - FIGURE H
WARNING: To reduce the risk of injury, turn off and
remove battery from the tool before making any adjustments or
removing or installing attachments or accessories.
WARNING: Do not attempt to tighten or loosen drill bits (or
any other accessory) by gripping the front part of the chuck and
turning the tool on. Damage to the chuck and personal injury may
occur when changing accessories.
To insert a drill bit or other accessory:
1. Grasp the rear half of the chuck (12) with one hand
and use your other hand to rotate the front half in the
counterclockwise direction, as viewed from the chuck end.
2. Insert the bit or other accessory fully into the chuck, and tighten securely by holding the rear
half of the chuck and rotating the front portion in the clockwise direction as viewed from the
chuck end.
TORQUE CONTROL - FIGURE I
This tool is fitted with a torque adjustment collar (13) to select the
operating mode and to set the torque for tightening screws. Large
screws and hard workpiece materials require a higher torque
setting than small screws and soft workpiece materials.
• Fordrillinginwood,metalandplastics,setthecollartothe
drilling position symbol
• Forscrewdriving,setthecollartothedesiredsetting.Ifyoudo
not yet know the appropriate setting, proceed as follows:
• Setthecollartothelowesttorquesetting.
• Tightenthefirstscrew.
• Iftheclutchratchetsbeforethedesiredresultisachieved,increasethecollarsetting
and continue tightening the screw. Repeat until you reach the correct setting. Use this
setting for the remaining screws.
ON-BOARD BIT STORAGE
Abitstorageslot(10)isbuilt-intotheareajustabovethebatterypackforeasybitstorageandaccess.
DRILLING
•Usesharpdrillbitsonly.
•Supportandsecureworkproperly,asinstructedintheSafetyInstructions.
•Useappropriateandrequiredsafetyequipment,asinstructedintheSafetyInstructions.
•Secureandmaintainworkarea,asinstructedintheSafetyInstructions.
•Runthedrillveryslowly,usinglightpressure,untiltheholeisstartedenoughtokeepthedrill
bit from slipping out of it.
•Applypressureinastraightlinewiththebit.Useenoughpressuretokeepthebitbitingbutnot
so much as to stall the motor or deflect the bit.
•Hold the drill rmly with two hands to control its twisting action.
I
13
H
12

   Find Your Products By Category